Step Motors
Integrated Motors
BLDC Motors
Size 23
Size 17
Drivers / Controllers
Stepper Drivers
Stepper Drivers/Controllers
BLDC Drivers
Power Supplies
Optical Encoders
Planetary Gears
Accessories
Additional Info
DRIVERS/CONTROLLERS | Microstepping Driver
 
R525 Stepper motor driver that allows for smooth motion microstepping MICROSTEPPING CLOSED-LOOP DRIVER
R525P

• Operates from +12 to 48 VDC
• Software selectable run currents from 0.1 to 5.0 Amp Peak
• Software selectable hold currents from 0 to 5.0 Amp Peak
(in 0.05 Amp increments)
• Step Resolutions from Full step, 2x, 4x, 5x, 8x, 10x, 16x, 25x, 32x, 50x, 64x, 125x, 128x, 250x, 256x Microstepping
• Communicating using RS485 and USB
• Operates in both Open loop and Closed loop modes
• Programmable analog input to change velocity and position.
• Programmable digital output for feedback.


BUY NOW - LINENGINEERINGSTORE.COM



 
  • Other Models
  • Options
  • Dimensions
  • Pin Outs
  • Electrical Specs.
  • Download
sq  
 OTHER MODELS AVAILABLE
   
 
4018 Standard Motor sq

MICROSTEPPING DRIVER
R208
....................................................

• Bipolar Step Motor Driver
• Operates from +12 to 24 VDC
• Phase current ranges from 0.35 to 2.0 Amps Peak
• Selectable Step Resolution from Full, Half, 1/4, and 1/8 microsteps



sq
4018 Standard Motor sq

MICROSTEPPING DRIVER
R701 & R710
....................................................

• Bipolar Step Motor Driver
• Operates from 24 to 80 VDC
• Phase current ranges from 1 to 7 Amps and 0.3 to 2 Amps
•10 Microstepping Driver
• Optically isolated Step, Direction, and Disable/Enable Inputs


 
4018 Standard Motor sq

MICROSTEPPING DRIVER+CONTROLLER
R256
....................................................

•Input Voltage of +12 to 40 VDC
• Phase Current Ranges from 0.2 to 2.0 Amps Peak
• Full step, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256
• RS485 Communication with Optional Converter
Cards Available



sq
4018 Standard Motor sq

SINGLE AXIS DRIVER+CONTROLLER
R356
....................................................

•Input Voltage of +12 to 40 VDC
• Phase Current Ranges from 0.3 to 3.0 Amps Peak
• Full step, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256
• RS485 Communication with Optional Converter
Cards Available


  dline
  ACCESSORIES
 
4018 Standard Motor sq

SUPPER TORQUE MOTOR
MODEL 4118
....................................................

• NEMA Size 17 Mounting
• Cost Effective
• Custom Windings Available (No addtional cost



sq
4018 Standard Motor sq

HIGH TORQUE MOTOR
MODEL 5718
....................................................

• High Torque
• Highest Step Accuracy
• High Resolution
• Custom Windings Available (No addtional cost)




 
4018 Standard Motor sq

CONVERTER CARD
RS485 to RS232
....................................................

• Allows user to connect the R256, R356, Silverpak 17C/CE, 23C/CE, and 34D motors to a PC via a standard serial port
• RoHS compliant



sq
4018 Standard Motor sq

CONVERTER CARD
USB485
....................................................

• Allows the user to connect their RS485 device to a PC via a standard USB port.
• UART I/F Supports 7 / 8 Bit Data, 1 / 2 Stop Bits and Odd/Even/Mark/Space/No Parity
• Data rate 300 => 250K Baud
• 384 Byte Receive Buffer / 128 Byte Transmit Buffer for high data throughput


   
  OPTIONS
   
 

Each R525P-RO comes with the following 4 cables in order for you to get up and running. No Designer’s Kit is required in order to operate one unit.

 

   
 

Model 090-00214 _090-00215



dline


R525P GUI SETUP
GUI SOFTWARE

   
 
line
 
   

 

 

 

 
DIMENSIONS
  Zoom In Click on drawing to zoom in
 

 

SilverPak 17D

   
   
   
 
   
   
   
   
   
   
PIN OUT
  R525P Overall Connector Location
 
P1 MOTOR CONNECTOR PIN-OUTS
SQPin SQFunction SQColor
SQ1 SQMotor Phase A SQRED
SQ2 SQMotor Phase A- SQBLUE
SQ3 SQMotor Phase B SQGREEN
SQ4 SQMotor Phase B- SQBLACK
   
 
P2 ENCODER CONNECTOR PIN-OUTS
SQPin SQFunction
SQ1 SQChannel B
SQ2 SQ5V input
SQ3 SQChannel A
SQ4 SQIndex
SQ5 SQGround
   
   
 
P4 I/O CONNECTOR PIN-OUTS
SQPin SQFunction SQDescription
SQ1 SQ+5 V out 5VDC out
SQ2 SQOpto COM This is a 5VDC input in order to optically isolate the logic signals (step, direction, disable pins). If no isolation is required, you can connect this pin to Pin 1, the 5VDC output.
SQ3 SQDisable pin Enable/Disable pin. When pin is low, or touching Pin 12 Ground, the driver is disabled. If left alone (high), driver is enabled
SQ4 SQRS485/A Communication line for RS485 connection. Used for dasiy chaining multiple units
SQ5 SQGround Power Supply Ground
SQ6 SQPOWER+VE Motor Power Supply Voltage, +12 to 48VDC
SQ7 SQDirection Direction input. Default connection will rotate the motor CCW. If this input is low, or touching Pin 12 Ground, rotation will be CW.
SQ8 SQAnalog input This input can take a potentiometer
SQ9 SQStep input Step pulse input. The step clock input will receive a clock pulse input (TTL squarewave signal, 0 to 5VDC), where one pulse will move the motor one step
SQ10 SQRS485/B Communication line for RS485 connection. Used for dasiy chaining multiple units
SQ11 SQOutput Via the GUI, user can choose to disable the unit, change motor direction, close upon fault, toggle when index is detected on the encoder, close when motor is stalled, moving or holding
SQ12 SQGround Signal ground, also known as digital ground
   
 
Motor Connection View
 
   
 

 

 

sq ELECTRICAL SPECS.
   
 
  • OPERATES FROM +12 to 48 VDC
  • DRIVE CURRENTS (per phase): 0.1 to 5.0 Amps Peak
  • ISOLATED INPUTS:Step,Clock, Direction, and disable
  • STEP FREQUENCY (Max): 1 MHz
  • STEPS PER REVOLUTION (1.8° MOTOR): 200, 400, 800, 1600, 2000, 3200, 5000, 6400, 10000, 12800, 25000, 25600, 50000, 51200
  • MICROSTEP RESOLUTIONS (1.8° MOTOR): Full step, 2X, 4X, 5X, 8X, 10X, 16X, 25X, 32X, 50X, 64X,125, 128X, 250X, 256X
  • OPERATING TEMPERATURE: Heatsink maximum temp 85°C.

 

 

 

   
sqDOWNLOAD
 
sq
DOCUMENTATION:

R525P User Manual


SOFTWARE
ZIP R525P GUI
ZIP USB DRIVER


 
  Dimensions
   
  INPUT VOLTAGE:+24 to 48 VDC

DRIVE CURRENT(PER PHASE):0.3 to 2 Amps or 1 to 7 Amps

ISOLATED INPUTS: Step Clock, Direction, Enable & Disable

STEP FREQUENCY (MAX): 200 kHz

STEPS PER REVOLUTION (1.8º MOTOR): 2000
   
sq


 
  Do You Also Need
   
Do You Also Need

sq